CPWC simulation on a matrix array with the USTB built-in Fresnel simulator

In this example we show how to use the built-in fresnel simulator in USTB to generate a Coherent Plane-Wave Compounding (CPWC) dataset using a 2D matrix array probe and illustrate how it can be beamformed with USTB.

This tutorial assumes familiarity with the contents of the 'CPWC simulation with the USTB built-in Fresnel simulator' tutorial. Please feel free to refer back to that for more details.

by Alfonso Rodriguez-Molares alfonso.r.molares@ntnu.no and Arun Asokan Nair anair8@jhu.edu 29.03.2017_

Contents

Close all previously opened plots and define the F-Number we will be using.

close all;

F_number=1.7;

Phantom

We start off defining an appropriate phantom structure to image. Our phantom here is a single point scatterer. USTB's implementation of phantom comes with a plot method to visualize the phantom for free!

pha=uff.phantom();
pha.sound_speed=1540;               % speed of sound [m/s]
pha.points=[0, 0, 20e-3, 1];...     % point scatterer position [m]
fig_handle=pha.plot();

Probe

The next UFF structure we look at is probe. It contains information about the probe's geometry. USTB's implementation of probe comes with a plot method too. When combined with the previous figure we can see the position of the probe respect to the phantom. Here, we shall set the probe to be a matrix_array type.

prb=uff.matrix_array();
prb.N_x=16;                 % number of elements in azimuthal direction
prb.N_y=16;                 % number of elements in elevational direction
prb.pitch_x=600e-6;         % probe pitch in azimuth [m]
prb.pitch_y=600e-6;         % probe pitch in elevation [m]
prb.element_width=570e-6;   % element width [m]
prb.element_height=570e-6;  % element height [m]
prb.plot(fig_handle);

Pulse

We then define the pulse-echo signal which is done here using the fresnel simulator's pulse structure. We could also use 'Field II' for a more accurate model.

pul=uff.pulse();
pul.center_frequency=3e6;         % transducer frequency [MHz]
pul.fractional_bandwidth=0.6;     % fractional bandwidth [unitless]
pul.plot([],'2-way pulse');

Sequence generation

Now, we shall generate our sequence! Keep in mind that the fresnel simulator takes the same sequence definition as the USTB beamformer. In UFF and USTB a sequence is defined as a collection of wave structures.

For our example here, we define a sequence of plane waves at various transmit angles (as defined in tx_angles). Apodization is set to none.

alpha_max=1/2/F_number;                     % Maximum (in absolute value) plane wave angle [rad]
N=15;                                       % Number of plane waves
tx_angles=linspace(-alpha_max,alpha_max,N); % Transmit angles for plane waves [rad]
seq=uff.wave();
for n=1:N
    seq(n)=uff.wave();
    seq(n).probe=prb;

    seq(n).source.azimuth=tx_angles(n);
    seq(n).source.distance=Inf;

    seq(n).sound_speed=pha.sound_speed;

    % show source
    fig_handle=seq(n).source.plot(fig_handle);
end

The Fresnel simulator

Finally, we launch the built-in simulator. The simulator takes in a phantom, pulse, probe and a sequence of wave structures along with the desired sampling frequency, and returns a channel_data UFF structure.

sim=fresnel();

% setting input data
sim.phantom=pha;                % phantom
sim.pulse=pul;                  % transmitted pulse
sim.probe=prb;                  % probe
sim.sequence=seq;               % beam sequence
sim.sampling_frequency=41.6e6;  % sampling frequency [Hz]

% we launch the simulation
channel_data=sim.go();

USTB's Fresnel impulse response simulator (v1.0.7)
---------------------------------------------------------------

Scan

The scan area is defines as a collection of pixels spanning our region of interest. For our example here, we use the linear_3D_scan option, which is defined with three components: the x-dimension (azimuthal) range, the z-dimension (depth) range and the y-dimension (elevational) range. scan too has a useful plot method it can call.

scan=uff.linear_3D_scan('radial_axis',linspace(-4e-3,4e-3,200).','axial_axis',linspace(18e-3,22e-3,100).','roll',0);
scan.plot(fig_handle,'Scenario');    % show mesh

Pipeline

With channel_data and a scan we have all we need to produce an ultrasound image. We now use a USTB structure beamformer, that takes an apodization structure in addition to the channel_data and scan.

mid=midprocess.das();
mid.dimension = dimension.both;
mid.channel_data=channel_data;
mid.scan=scan;

mid.receive_apodization.window=uff.window.tukey50;
mid.receive_apodization.f_number=F_number;

mid.transmit_apodization.window=uff.window.tukey50;
mid.transmit_apodization.f_number=F_number;

b_data=mid.go();
b_data.plot();

USTB General beamformer MEX v1.1.2 .............done!

The pipeline structure allows you to implement different beamformers by combination of multiple built-in processes. By changing the process chain other beamforming sequences can be implemented. It returns yet another UFF structure: beamformed_data.

% To achieve the goal of this example, we use delay-and-sum (implemented in
% the *das_matlab()* process) as well as coherent compounding.

Published with MATLAB® R2020b